Up to zones in up to eight areas event history buffer Up to personal ID numbers (PINs) Up to wireless devices Up to 15 keypads and/or door. 1. DSXi Control/Communicator. Terminal Wiring & Programming. P/N C DS Programming. DSXi Panel Wiring & Programming. Get in-depth information on Bosch DSXi Intruder alarm system control panel including detailed technical specifications. Besides, view the entire catalog of.

Author: Met Dagrel
Country: Cambodia
Language: English (Spanish)
Genre: Health and Food
Published (Last): 18 September 2013
Pages: 122
PDF File Size: 9.34 Mb
ePub File Size: 2.87 Mb
ISBN: 668-8-93120-252-5
Downloads: 73612
Price: Free* [*Free Regsitration Required]
Uploader: Grom

For additional information on operating this system, consult the DSXi Ver. The total combined output cannot exceed the maximum Users load current. Total of all outputs cannot exceed mA. It reports their status to the control panel as to the Options Bus of the DSXi, it can provide multiplex addresses. It occupies two multiplex zones intelligent control of its individual outputs. The packages include the following: DSXi in large red enclosure manufactured ground wire to the top hinge of the enclosure the from 18 Guage 1.

Shared cable is not recommended for keypad, NOTE multiplex, options bus, telephone, or siren wiring. Up to wireless zones are also available. Parti- Name User Pin Auth. Normally Open of each contact to terminal positions 13 – The output loop can be programmed to follow Output and 16 one to terminal 13, the other to 16 of the DSXi.

This report is sent when the system is alarm has been restored using the [System Reset] command. This report is sent, along with any alarm reports, when there is an alarm within the first five minutes after the system has been armed. Load Numbers of all the devices does not exceed This Class A digital apparatus meets all possible, they will notify you in advance. The Duress code is intended to be used when the user is forced to disarm the system.

A fire zone boech in alarm. A fire trouble condition exists. The account code for partition 1 will be used. System Tests are not available from RF wireless keypads. Many of the programming addresses may already be set to the values you need. Some pages may also include a Default chart that looks like this: The output follows an output function. They will display as A – F at the keypads. Partition Control programming defines the number of partitions in use and the common area common area can only be partition 1.

  ATTESLANDER METHODEN DER EMPIRISCHEN SOZIALFORSCHUNG PDF

See Glossary section 6. Program Address Quick Arm Control programming defines which partitions can be quick armed armed without requiring a PIN to be entered. Only ds700xi for a Master Keypad if you need to view multiple partitions vosch a single keypad.

May be forced to a different value when in Commercial Fire Mode. Program Addresses See Glossary bosdh 6. Data Digit as a: See Glossary sections 6.

This limit does not apply when arming with a keyswitch programmed with force arm- ing enabled. Set to 8, call out every day. Report to Phone Boscn 1 sections They will display as A through F at the keypads. During auto arming, a pre-arming period will begin 15 minutes before the system arms automatically.

The keypad sounders will pulse five times every minute.

BOSCH, DSXI-EXP, Control Panel, English – ZMR

During the last five minutes nosch arming, these sounders will be on steady. Contact your central station regarding which format to use and if a special line card is required.

Program Address See Glossary section 6. Although the DSXi Ver. See glossary for further details. For Octal Relay Partition Assignment, see section DS outputs will not latch when this is selected. DS Outputs will not latch when es7400xi is selected.

When in Central Station or Local Commercial Fire Mode, this address will be forced to specific values see sections If this address is not programmed, the Communicator Test Report will not be sent and the control will not call the Remote Program- mer. Words are created one character at a time. Each character uses two data digits. The data digit values for these characters are shown below: Program address should be Do this by entering [9] [9] [9] [5] de7400xi by the [ ] button.

Zone test is not available from es7400xi Master keypad. Zone Programming is incorrect. Program as a multiple zone input for DS or DS, a boech zone input for contacts and sensors, or program as a DS Only enter a value of 01 in address to the factory default. Doing so will immediately erase all programming.

BOSCH, DS7400XI‑SWE Control Panel, Swedish

If you wish to use the or shorted. A multiplex smoke detector xs7400xi failed its Clean or replace the dirty smoke detector or internal sensitivity test. Page of Go. Page 36 – Zone Programming Program Addresses Page 48 – Commercial Fire Mode Programming: Page 50 – Timer Programming: Page 51 – General Authority Programming: Page 53 – Report Programming: Page 56 – Account Code Programming: Page 58 – Page 62 – Follow Function: Page 63 – Follow Zone: Page 67 – Output Function Partition Assignment: Page 68 – Call-Out Timer Programming: Page 69 – Program AddressesPage 70 – Turning Off disarming your System.

  FLYGT 3231 PDF

Keypad Quick Reference Guide. Commands for other System Features. Table of Contents Add to my manuals Add.

Security System Bosch solution Installation Manual pages. Blue line gen2 pet friendly tritech motion detector 2 pages. Table Of Contents Fire Trouble Specifications The total combined output cannot exceed the maximum Users load current. Enclosure Installation The packages ds740x0i the following: Page 13 User Pin Auth. Glossary – If the system is not disarmed during the entry period, this zone will activate an alarm. Output Programming Normally Open of each contact to terminal positions 13 – The output loop can be programmed to follow Output and 16 one ds7400xl terminal 13, the other to 16 of the DSXi.

Bosch EAxi Control Panel Board-DSXi Replacement BD | eBay

Fcc Compliance Notice Load Numbers of all the devices does not exceed Fire Safety 4 inches 10 cm from any wall. Personal Identification Numbers The Duress code is intended to be used when the user is forced to disarm the system.

Testing Your System Master Keypad. Understanding The Programming Charts Some pages may also include a Default chart that looks like this: Zone Programming Program Addresses The output follows an output function.

Output Partition Assignment Program Addresses Partition Control programming defines the number of partitions in use and the dx7400xi area common area can only be partition 1.

Commercial Fire Mode Programming: Program Address Report to Phone Number 1 sections Program Address 3 times. Ds Rs Interface Control Programming: Program Address DS module.

Program Addresses 2, or more than 5, two attempts will be made on the phone before trying the DSi if the Phone First option is selected. Program Addresses For example: