ASTM A is the specification that covers the general requirements for flat- rolled stainless and heat-resisting steel plate, sheet and strip. It does not reference. 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel, product specifications that reference Specification A/. ASTM A/AM Standard Specification for General Requirements for Flat -Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and.
|Published (Last):||25 May 2018|
|PDF File Size:||7.75 Mb|
|ePub File Size:||5.55 Mb|
|Price:||Free* [*Free Regsitration Required]|
Users of this ast are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Material Test Report and Certi? Hardness conversion shall be done using the applicable tables in Test Methods and De?
In this case, the purchaser shall inform the seller and agree upon the requirements and these requirements shall be so stated on the purchase order. Bright Annealed Finish—See Note 4.
ASTM A480 Plate Thickness & Flatness Tolerances
Originally approved in Interspersement of different melts is permissible if they are of approximately the same nominal thickness and are heat treated in the same operating period and under the same conditions time and temperature.
Combining values from the two systems may result in nonconformance with the speci? This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Note that Practices A requires the test to be performed on sensitized specimens in the low-carbon and stabilized types and on specimens representative of the asshipped condition for other types.
Combining values from the two systems may result in nonconformance with the specification. Hard 19 16 13 26 19 16 12? Within the text, the SI units are shown in brackets, except that when AM is speci? When the material is too thin to allow hardness testing using any of the Rockwell super? Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Finishes for sheet are actually shown in Section Such a requirement for an element not listed in the product speci? The allowable variation of a particular element in a single sample for product analysis is permitted to be either above or below the speci?
In case of dissatisfaction with the results of the test, the seller is permitted to make claim for a astj within that time. The tension test specimen shall conform to the appropriate sections of Test Methods and De? A skilled operator can generally blend this? Refer to Section The inside of the coil shall also be marked or shall have a tag or label attached and marked with the information of The characters shall be awtm such size as to be clearly legible.
It is neither practical nor necessary to specify limits for unspeci? Various production methods may be used to obtain these? This standard has been approved for use asgm agencies of the Department of Defense.
ASTM A Plate Thickness & Flatness Tolerances – Rolled Alloys, Inc.
Number of Tests Finishes for plate are actually shown in Section The marking shall be sufficiently stable to withstand normal handling. This material aa480 report shall reference the product speci? NOTE 2—The tolerances in this table include crown tolerances. The gage number shall not be a basis for rejection.
All austenitic chromium-nickel types except the H types are expected to be capable of passing this test. NOTE 2—If the longer dimension is under 36 in. The purchase order requirements shall not take precedence if they, in any way, violate the requirements of the product specification or this specification; for example, by waiving a test requirement or by making a test requirement less stringent.
Committee A01 has identi? However, unless the order speci? The material shall be accepted if the results of retests on retreated material are within the speci? It is permitted to round the edges to a asrm B Recommended cleanup allowance which, unless otherwise speci?
ASTM A Specification | Penn Stainless Products
Approved November 15, If the hardness difference between the two ends of the coil exceeds 5 HRB, or equivalent, or if the material is temper rolled, tensile properties must be determined on both coil ends.
B Maximum deviation from a horizontal? All widths and lengths 1 16 18 1 16 18 Over mm 1.
The manufacturer is permitted, if necessary, use a lower temperature resolution anneal or a stabilization anneal after a high temperature solution anneal in order to meet corrosion test requirements. The material shall undergo mechanical tests such as tension test, hardness test, and bend test.